The basic materials used in SANDAO ge rtv silicone are canvas, rubber or high-grade plastic. The choice depends on the use, for example, indoor or outdoor. Climate too plays a significant role like places with high humidity and moisture. 2.
The product is not likely to accumulate too much heat. Its powerful cooling system is designed to maintain the proper temperature of mechanical parts, allowing it to have good heat dissipation. 3.
The product has the advantage of stable mechanical properties. Having been treated under extremely cold temperatures, its mechanical components are tensile enough to withstand extreme industrial conditions. 4.
People say that it has been used for a long time, and no loose lines, inferior sutures or low-strength lines can be found.
Epoxy resin potting sealant SD6341
Epoxy resin potting sealant SD6341 is a two-component electronic material used for general electronic component sealing and circuit board sealing. It can be cured at room temperature or heated, and the cost is lower. Temperature during curing is low and the highest exothermic temperature is less than 50 ℃. Good surface gloss, low shrinkage, excellent moisture resistance and insulation after curing.
Epoxy resin pouring sealant is widely used in silicon steel materials, roller core materials, coil windings, capacitor bushing and other important radiating and high temperature resistance electronic appliances, such as transformers, motors, radiators, sensors, electromagnets, PCB plates, solenoid valves, air conditioners, power module, electromagnetic clutch, automobile parts, etc.
◪ Two-component 4:1 ratio, 100% solidification, no solvent, no pollution, no toxicity.
◪ Good weather resistance, water resistance, oil resistance, acid resistance, high temperature resistance, insulation, flame retardant, cracking resistance and so on.
◪ Can be cured at room temperature and heating, high bonding strength. Stable performance, good toughness and filling after curing, excellent physical, mechanical and insulation properties.
◪ It has low viscosity after mixing, no need of vacuum defoaming at room temperature, and long operating time, so it’s a kind of ideal pouring glue.
◪ For some larger parts of the pouring and sealing, can be one-time molding, more operational advantages.
◪ Achieve actually measured high thermal conductivity: 0.8w/m.k
|Item||Condition||Part A||Part B||Mix liquid|
|Appearance||Visual||White/black Viscous liquid||Transparent / brown liquid||White/black liquid|
Usage: 1.Mixing: mix part A and part B at 4:1 ratio by weight, potting after stir well. The operating time after mixing is 60 minutes at 25 ℃.
2.Solidification: at 25 ℃, it will harden at 6 for 8 hours, and at 80 ℃ for 1 hour. It can be assembled after hardening. Tests typically take place after 24 hours of curing.
Notes:This data is measured by the technicians in the laboratory, which has certain reference value for the users. However, because the usage methods and conditions of each user are different, it is suggested that the users should find out the best technology and method according to their own conditions.
|Feature after curing|
|Dielectric loss tangent||25℃，1MHZ||<0.01|
|Shear temperature range||Mpa||>10|
|Operating temperature range||℃||-40~150|
Attention: 1, This kind of products are not dangerous goods, according to the general chemical storage and transportation, the storage period is 1 year.
2, A component should be stirred properly before use (as there will be precipitation after long period of time, it does not affect the performance after stir well,); after accurate weighing of component A and component B, please stir well and then use it.
3, The mixing amount of glue should not be too large, otherwise, the operating time will be shortened which lead to waste if cannot use out timely.
Notes:The above performance data are typical data of the product at humidity 70 ℃, temperature 25 ℃,for customer's reference only. Customers are kindly requested to use the measured data.
Epoxy resin potting and sealing adhesive
SD6341 epoxy potting compound is a two-component electronic material used for Potting of general electronic components And circuit board sealing.
White/black viscous liquid
It can be cured at room temperature, and can be Cured by heating. After curing, the surface gloss Is good, the shrinkage rate is low, and the Moisture resistance and insulation Performance are excellent.
Green environmental protection
Non-toxic, non-corrosive, free of harmful Substances.
Plastic bottle packaging
packaging specifications: 1.25kg/ set.
With expanded operations worldwide, Huizhou SANDAO New Material Co., Ltd is moving to a higher and more professional level in manufacturing Two-component addition-type potting adhesive TDS. 2.
Located in a place where has industrial clusters, the factory enjoys a geographically advantage. This advantage enables the factory to cut costs in sourcing raw materials or send the products to process. 3.
The core value of our company to gain success is to keep changing. We have a keen sense of the market trends which constantly changes, and we keep innovating so as to progress continuously. Get info! Sustainability is a promise to our customers and to the environment. It’s our global heritage, and the one we take very seriously. While creating products that meet customers' demand, we never stop striving to achieve the lowest possible ecological footprint. Get info! Environmental protection is the priority of our business. We have initiated advanced production technology to minimize the negative impact on our environment.