During the design and developing stages, SANDAO ge rtv silicone has been invested a lot of energy and capital to improve its rate of identification for writing and drawing. 2.
Its quality is ensured with the quality control and management system in our factory. .3.
SANDAO offers exceptional performance and high quality product. 4.
SANDAO is able to provide the most professional Two-component addition-type potting adhesive TDS solutions.
Sandao organic silicon electronic potting sealant SD9501
Sandao organic silicon electronic potting sealant SD9501 is synthesis organo silicon electronic pouring sealant with high elasticity and high transparent for electronic component, packing divided to A and B two component, mixes the A and B two components and fully agitates before filling and sealing; The mixture has good fluidity, good elasticity after curing, excellent resistance to high and low temperature, excellent electrical performance, ozone resistance and atmospheric aging resistance, which is used for long-term outdoor use. The products are in full compliance with the requirements of the EU RoHS Directive.
◪ Resistance to high and low temperature -60~260℃
◪ Sandao organic silicon electronic pouring sealant with the advantages of automatic leveling, automatic remove air bubbles, high viscosity, high temperature resistance, moisture proof and waterproof insulation, easy rework, it can used as adhesive, sealing, waterproof, moisture-proof, mildew proof, dustproof, filling seal, shock absorption, aging resistance and so on.
This potting sealant is fit for electrical and electronic components which required for waterproof and insulation, used for adhesive and sealing LED junction box, wind power motor, PCB substrate, etc., as well as various AC/DC power supply modules, control modules, automotive HID stabilizers, lights and various power control modules,etc.
Wind energy motor bonding
|1||Before curing||Part A||appearance||transparent||black||white|
|5||viscosity (m Pa·S)||50-150||50-150||50-150|
|7||viscosity after mix(m Pa·S)||1000～1300||1000～1300||1000～1300|
|10||60℃ heating curing time（min）||30||30||30|
|11||Room temperature curing time（hr）||24||24||24|
|12||After curing||hardness（shore A,24hr）||30～50||30～50||30～50|
|15||dielectric strength（kv/mm）||≥ 20||≥ 20||≥ 20|
|16||bake（80℃ 144h）||Not yellow|| -||-|
Kind remind: The above properties were measured at 25 ℃ and 55% RH for 7 days. The parameters provided in this data may vary depending on the environmental, temperature and humidity conditions;
Silicone electronic potting
SD9501 integrated silicone electronic potting Compound, high elasticity, high transparent Electronic components potting glue.
White/black viscous liquid
Good fluidity, good elasticity, excellent resistance to high and low temperature, excellent electrical performance.
Green environmental protection
Non-toxic and non-corrosive,The products fully comply with the requirements of EU RoHS standard
Iron bottle packaging
packing specification: 20kg/set ,component A/10kg .component B/10kg.
1. Mix the two components according to the weight ratio of A:B=1:1 and stir well, then remove air bubbles (vacuum or static) and then fill it up. Note: must stir evenly, otherwise affect the properties of solidified compounds; should be used within the applicable period of the sealant.
2. About mixing; After mixing component A and component B, manual or mechanical mixing can be adopted. When mixing, high temperature should be avoided because of high speed and long time agitation, so as to avoid shortening operation time and speeding up solidification, in case operate time is not enough. The surface of the product must be cleaned before it is sealed.
3. The work site and working environment must maintain the air circulation, in case the concentration is too high after the chemical liquid volatilize in the air, causes the staff to be sick (respiratory tract and skin irritation etc.).
4. The surface in contact with the compound must be cleaned. It is forbidden to mix the compound with organic compounds containing nitrogen, phosphorus, sulfur and heavy metal ions containing Sn,Ph,Hg, Bi, As , in case affect the curing of the compound.
Packaging and preservation
20kg/ set (component A 10kg and B 10kg), transported as non-dangerous goods, stored in a cool (room temperature) dry place, guarantee period is 6 months.Company Features1.
SANDAO precedes many other companies that manufactures Two-component addition-type potting adhesive TDS. 2.
SANDAO is emerging as the biggest supplier of Two-component addition-type potting adhesive TDS to all customers. 3.
The tenet of Two-component addition-type potting adhesive TDS supports the growth of SANDAO in this industry. Welcome to visit our factory! Adhering to the spirit of ge rtv silicone enables SANDAO to continue to provide more innovative and high-quality Two-component addition-type potting adhesive TDS and gain worldwide recognition. Welcome to visit our factory!