Hot products
◪ Fast curing, high viscosity, high strength, impact resistance, high insulation, transparent, low smell, no corrosion.
◪ Epoxy resin AB sealant can resist most chemicals and solvents.
◪ Temperature-resistant -40-120 ℃.
Sandao fast drying Epoxy resin AB sealant are used for bonding of metal, ceramic, glass, electroplating / paint / magnetic materials, such as aircraft motor, automobile, machinery, ship, electronics, electrical apparatus, instrument, building, furniture, toys,. high temperature resistant parts such as railway vehicles ,etc, AB glue can also be used to adhesive water tank, oil road, carburetor, cylinder cover, exhaust pipe, bushing of driving shaft, plastic parts such as baffle, vehicles lamp glass, car handle, etc.
Glass bonding
Electroplating paint bonding
Ceramic bonding
Motor component bonding
Mechanical component bonding
Furniture bonding
| Epoxy resin AB glue | SD805 part A | SD805 part B | ||
| Appearance /color | transparent | transparent | ||
| Viscosity (mPa.s 25℃) | 8000-15000 | 11000-18000 | ||
| Specific gravity (g/ml 25℃) | 1.0-1.05 | 1.0-1.05 | ||
| Ratio（weight ratio pbw） | 1 | 1 | ||
| Gel time under normal temperature（25℃）20g | 5mins | |||
| Curing condition | / | / | ||
| Temperature range（℃） | -40℃-120℃ | |||
| Hardness（Shore-D） | 73/80 | |||
| Epoxide equivalent（g/eq） | 185/190 | / | ||
| Active hydrogen equivalent g/eq | / | 185/195 | ||
| Distortion temperature HDT | 80℃ | |||
| Volume resistivity（Ω.cm）25℃ | 5.0×1016 | |||
| Surface resistivity（Ω.cm）25℃ | 7.5×1012 | |||
Shear strength of different materials（Mpa） | ||||
| Aluminum / copper | 15-18 | |||
| Steel | 16/19 | |||
| ABS | 6-7 | |||
Put on AB glue gun and put on the thread mixing head. The thickness of adhesive layer should be 0.05mm, the coated object should be clamped immediately, and the maximum bonding strength will be guaranteed by uniform contact pressure.
To obtain the highest mechanical strength, the surface of the material can be polished or sandblasted, and then the dust and oil stains on the surface can be scrubbed with a special solvent.
Adhesive should be put on both sides of the object and fix the splice in avoid of dislocation.
Do not mix the lid of A and B to prevent contamination of the adhesive.
1. AB adhesive is slightly irritating, please wear gas mask and anticorrosion gloves when operating.
2. Cover at any time after each extraction, lest moisture absorption affect curing and performance.
3. Mass use of this product needs to be in a well-ventilated place.
Epoxy resin AB adhesive is packed with AB mixed pipe, 64g/ pcs, transported as non-dangerous goods, should be stored in a dry, shady place (below 5 ℃ ~ 26 ℃), the shelf life is within 12 months from the date of manufacture.
Product Name: epoxy anchoring adhesive
Product Code: HM-500
Product Description:HM-500 chemical anchor adhesive ,a multi-purpose,two components,high strength,high modulus moisture-tolerant adhesive,used for connection of post-installed rebars and anchors
USES:1. Fix steel bar and bolt in concrete.
2. Fix bracket of curtain wall stone hanging.
3. Strengthen construction structure and bar anchoring.
4. Fix various equipment base.
5. Anchorage connection between steel structure and concrete structure.
6. For Reconstruction and extension project reinforcement of railway, highway, bridge and water conservancy project.
7. Fix billboards, tunnel line, sound insulation board of elevated road and barrier.
Features: 1.Modified epoxy resin,no styene
2.High strength and high modulus,good toughness
3.Ageing,heat resistance
4.Moisture tolerant,long term load stability in a damp enviroment
5.Acid and alkali ,seismic resistance ,no expansion
6.Excellent thixotropy,especially suitable for anchoring the side or top
7.Binocular straight mixed package,with special glue gun without prepare
1.Drill hole to the diameter and depth required. The diameter must be in accordance with anchor size.
2.The drill hole must be cleaned with air blower, starting from the bottom of the hole.The drill hole must be thoroughly cleaned with steel brush. After brush, to use air blower to clean the drill hole again.
3.Inject chemical anchor resin into the hole, starting from the bottom, while slowly drawing back the static mixer. In any case avoid entrapping air. For deep holes extension tubing can be used.
4.Insert the anchor with a rotary motion into the filled drill hole. Some adhesive must come out of the hole.
5.During the resin hardening time the anchor must not be moved or loaded.
Test Report
| A (epoxy) | white paste |
| B (hardener) | red or black paste |
| viscosity of mixture | 18-22 Pa.s |
| density of curing material | 1.50 g/cm3 |
| mixture ratio | 3:1 |
| shelf life | 18 months |
| splitting tensile strength | ≥8.5 Mpa |
| bending strength | ≥50Mpa |
| compressive strength | ≥60 Mpa |
| thixotropic index | ≥4.0 |
| sagging moblity | ≤2.0 mm |
| distortion temperature | 65℃ |
| steel-steel(steel sleeve)tensile antti-shear strength | ≥10Mpa |
| under the constraint draeing condition,ribbed steel bars and C30,25,L=150mm | ≥11 |
| adhhesion strength with concrete C60,25,L=125mm | ≥17 |
| steel-steel T impact stripping length | ≤25mm |
| non-volatile matter content(solid content) | ≥99 |
| wet and heat ageing resistance ability | compared with the short-term rsults at room temperature,the decrease rate of shear strength:≤12% |
| heat aging resistance | compared with the short-term results at same temperature 10min,the decrease rate of shear strength:≤5% |
| freezing and thawing resistance ability | compared with room temperature ,short-term results,the shear strength decrease rate is not greater than 5% |
| fatigue stress resistance ability | after 2×106 times continuous sine wave fatigue loads,specimen does not destroy |
| resistance to stress for a long time | steel-steel tensile shear specimens does not destroy,and creep deformation value is less than 0.4mm |
| resistance to salt fog effect | compared with the control group,the strength decrease rate:≤5%,and shall not have cracks or come unglued |
| alkaline medium resistance ability | compared with the control group ,the strength does not decrease ,and as the concrete damage,and shall not have cracks or come unglued |
| acid medium resistance ability | concrete damage,and shall not have cracks or degumming |
Operable time and curing time
| ambient temperature(℃) | -5 | 0 | 10 | 20 | ≥30 |
| operation time(min) | 60 | 45 | 30 | 15 | 20 |
| curing time(h) | 72 | 48 | 24 | 12 | 6 |
Cases
HORSE 390ml chemical anchor adhesive have been proven in more than 70,000 structural strengthening projects worldwide. The projects include civil engineering, bridges, airports, railway tunnels, sea ports, Wate Resources Hydropower Engineering projects, historic buildings, etc. Many of them are world-class landmarks,such as the Oriental Pearl Tower, Shanghai Center, and the Hangzhou Bay Bridge.
Packaging and shipping
packaging:390ml/tube,30tubes/box,use plastic hard tube package
Shipping: By air, By sea, By train
Pay for Transport
Company
Shanghai Horse Construction is an ISO 9001:2008 Certified company started in 2008. It is a
manufacturer of carbon fiber as well as epoxy resin for structural strengthening for more than 10
years based in Shanghai, China. And now is the top leader of carbon fiber fabric and reinforcement
materials. Its plant is located in Shanghai and the company has over 20 branches and offices allover
China.
Epoxy injection type anchor glue is double components modified epoxy resin glue. This product adopted completely new hose single package with glue gun injecting. And they can be mixed through the static mixer, and injected directly into the hole and then cured.
Copyright © 2019 Huizhou Sandao New material Co., Ltd. | All Rights Reserved
Hello, please leave your name and email here before chat online so that we won't miss your message and contact you smoothly.
